English 
Stators and Rotors for Fan Motor
Widely applied for stand, wall and ceiling fan motors featuring low noise, high efficiency...
Read MoreStator Rotor for Water Pump
Induction Asynchronous Water Pump Stator Rotor Lamination, stator winding
Turbo Positive Displacemnt pump motor stator rotor core and winding armature
The basic category of pumps are three main types. Firstly, Turbo pump, such as Centrifugal pumps, Mixed-flow pumps and Axial-flow pumps. Secondly, Piston pumps and plunger pumps for Reciprocating pumps; Gear pump and Screw pumps for Rotary pumps. Last, Special types pumps, such as Hydraulic Ram pumps, Vortex pumps and Jet pumps. The stator and rotor can also fit in submersible pumps and all the others. There are nearly 70 types of pumps for different applications and for various working sites. It is said the most rapidly usage among all motors.
Meet UL regulations:
- Tayguei is a professional manufacturer of stator rotor lamination nearly 40 years. There are wide range of dimensions, ranging from 90mm x 47m to 220mm x 120mm for different designs. They are standard sizes to fit in IEC (the International Electrotechnical Commission) regulations. Within IEC, there are standard frame numbers to let motor designers to refer to the related size of stator rotor. If your motor meet with IEC regulation, you can easily find the suitable stator rotor lamination from us.
Tolerance:
- We can control the tolerance to make stator smooth and accurate. Please understand the tolerance differs from different material of silicon steel lamination and design of mold. Usually, it is within 0.03mm-0.05mm.
IE3/IE4 Efficiency:
- We are proud to claim that motors using our stator rotor passed the IE3/IE4 testing in UL laboratory. Our material is directly supplied from the top supplier, China Steel. With correct design and our rich experience on mold developing, we can guarantee the quality.
- The higher the stacking height, the greater power you can get. Pump motors by using our stator rotor can reach horse power from 0.25HP to 20HP. Certainly, the bigger the outer diameter of stator, the bigger horse power you can get. Furthermore, it also related to the way of winding on the rotor. Die-casting is also important for the efficiency for better electrical conductivity ratio. Different designs for aluminum die casting rings in height, leaves and columns according to each customer's design. The dimension of central hole is also important to consider. It related to the outer diameter of the shaft of motor. If you want to reach high RPM, you must notice the number of poles. Normally, the larger of pole numbers, the smaller RPM. Generally, it is 2 Poles for pump motor, especially for submersible pumps. Otherwise, it can not be able to pump water up without enough RPM. Finally, there are options for screw holes for different mounting way in motors. Please let us know if you need those screw holes or not.
Result 1 - 12 of 12
108x70 mm Stator Rotor Lamination for Two Poles and Four Poles Motor
TG10870
TG10870 is mostly applied for Washing machines & garage doors. The outer diameter of stator is 108 mm and the inner diameter is 70 mm. As you can see the slot of stator is more square to provide large space for winding. This kind of slot-shape provides better torque and suitable for S3 working duty motors. The slot of rotor is short (Type A) to provide better torque. Most customers use it in 4 poles single phase or three phases induction motors, ranging from 0.5HP ~ 2HP. The slots of stator are 24T and the slots of rotor are 34T. Rotors can do V-shape to rotate clockwise or counter-clockwise.By using this stator rotor, you can reach low noise, long lifespan and low maintenance.
114x56 mm Stator Rotor Lamination for Two Poles High Efficiency Motor
TG11456
TG11456 is mostly applied for industrial motors, water pump motors, blower motors, sawmill motors and high efficiency motors, especially great for pump motors. The stator outer diameter is 114 mm and the stator inner diameter is 56 mm. Most customers use it in four poles design with single phase or three phases induction motors, ranging from 0.5HP ~ 2HP. The slots of stator are 24T and the slots of rotor are 29T.The rotor OD is smaller than the stator ID after stamping – No-Gap design. So that you can save one machinery. The rotor is not needed to do the lathing after stamping.By using this stator rotor, you can reach low noise, long lifespan and low maintenance. Approved by IE2, IE3, and IE4 authentication.
140x75 mm Stator Rotor Lamination for Two Poles and Six Poles High Efficiency Motor
TG14075
By using TG14075, you can reach low temperature, low current and high efficiency. This stator rotor is round shape and mostly applied for industrial motors, water pump motors and high efficiency motors. Water pump motors is the majority. The stator outer diameter is 140 mm and the stator inner diameter is 75 mm. Most customers use it in 2 poles design with single phase or three phases induction motors, ranging from 0.5HP ~ 2HP. It's suitable for the standard IEC frame no. 90L.The slots of stator are 24T and there are two types of rotors, one is with 18T for three-phase motor and the other is with 33T for single-phase motor. By the way, the rotor with 33T is with opening design to provide bigger torque. Applied with this stator rotor, you can reach low noise, long lifespan and low maintenance. Approved by IE2, IE3, and IE4 authentication.
160x80 mm Stator Rotor Lamination for Two Poles Motor
TG16080
With 2 types of rotors for options, TG16080 is square shape and mostly applied for power wood tools, water pump motors, air compressors, and also used in cranes. The stator outer diameter is 160 mm and the stator inner diameter is 80 mm. Most customers use it in 2 poles design with single phase or three phases induction motors, ranging from 2HP ~ 3HP. It's suitable for the standard IEC frame no. 100L.The slots of stator are 24T and the slots of rotor are 16T or 34T (2 types). You can see the slot shape of rotor is very short to provide bigger torque. This stator rotor is perfect for power wood tools, especially for saw tables. By using this stator rotor, you can reach low noise, long lifespan and low maintenance. Approved by IE2, IE3, and IE4 authentication.
160x88 mm Stator Rotor Lamination for Two Poles High Efficiency Motor
TG16088
With unique design of rotor, TG16088 is round shape and mostly applied for industrial motors, water pump motors, blower motors, sawmill motors and high efficiency motors. This model is better than TG16080. Customers use this stator rotor to make 2 poles, 2HP, 3-Phase motors can pass IE4 certification. Applied for 3HP motors, it can pass IE3.The stator outer diameter is 160 mm and the stator inner diameter is 88 mm. Most customers use it in 2 poles design with single phase or three phases induction motors, ranging from 2HP ~ 3HP, maximum 5HP. It's suitable for the standard IEC frame no. 100L.The slots of stator are 24T and the slots of rotor are 18T. There is a special design of rotor. There is an opening every 2 slots to provide better start-up. By using this stator rotor, you can reach low noise, long lifespan and low maintenance. Approved by IE2, IE3, and IE4 authentication.
90x47 mm Stator Rotor Lamination for Two Poles Motor
TG9047
Small water pump motors are widely used TG9047. This model is also highly welcomed in middle east market. The stator outer diameter is 90 mm and the stator inner diameter is 47 mm. Most customers use it in 2 poles design with single phase or three phases induction motors, ranging from 0.25HP ~ 1.5HP.Besides water pump motors, this motor core lamination is also applied for air compressor motors. The slots of stator are 24T and the slots of rotor are 18T. There are openings on the rotors to provide better permeability.Some of middle-east customers also use this stator rotor to make high RPM fan motors. By using this stator rotor, you can reach low noise, long lifespan and low maintenance. Approved by IE2, IE3, and IE4 authentication.
90x48 mm Stator Rotor Lamination for Four Poles Motor
TG9048A
TG9048A is mostly applied for water pump motors, blower motors and compressor motors. The special design of rotor is with opening on each slot. By doing so, rotor can provide bigger torque and better efficiency.The stator outer diameter is 90 mm and the stator inner diameter is 48 mm. Most customers use it in 2 poles design with single phase or three phases pump motors, ranging from 0.25HP ~ 1HP.The slots of stator are 18T and the slots of rotor are 23T. By using this stator rotor, you can reach low noise, long lifespan and low maintenance. Approved by IE2, IE3, and IE4 authentication.
90x50 mm Stator Rotor Lamination for Two Poles High Efficiency Motor
TG9050
TG9050 is round-shape stator rotor / motor core and mostly applied for water pump motors and submersible pump motors. TG9050 is accordance with the international pump motor standard. The stator outer diameter is 90 mm and the stator inner diameter is 50 mm.There are two types of rotors. Both rotors are with 18 slots, but the shape of slots are different. One is for submersible pumps to insert copper rods, so the slots are bigger. The other is for aluminum die-casting with an opening on each slots to provide better start-up.Most customers use this stator rotor it in 2 poles design with single phase or three phases induction motors, ranging from 0.25HP ~ 1HP. The slots of stator are 24T and the slots of rotor are 18T. By using this stator rotor, you can reach low noise, long lifespan and low maintenance. Approved by IE2, IE3, and IE4 authentication.
90x52 mm Stator Rotor Lamination for Two Poles High Efficiency Motor
TG9252
TG9252 is most common used in submersible pump motors and water pump motors. The stator is round shape, OD is 92mm and the ID is 52mm. There are two types of rotors with big shaft centers. Most customers use this stator rotor in 2 poles design with single phase or three phases induction motors, ranging from 0.25HP ~ 1HP.The slots of stator are 18T and the slots of rotor are 24T or 28T (2 types). Comparing with TG9050, the slots of stator is less but bigger to insert more copper wires.Usually, this model is with long stacking height. Therefore, we provide big shaft hole φ31.45 for customers with 28 slots rotors. If you would like to use it on the water pump motors, you may choose rotors with 24 slots which shaft hole is φ15.85. By using this stator rotor, you can reach low noise, long lifespan and low maintenance. Approved by IE2, IE3, and IE4 authentication.
100x53 mm Stator Rotor Lamination for Two Poles Motor
TG10053
TG10053 is our best seller stator rotor and mostly applied for angle grinders, pumps and fan motors. The stator outer diameter is 100 mm and the stator inner diameter is 53 mm. Most customers use it in two poles design with single phase or three phases induction motors, ranging from 0.25HP ~ 0.75HP.The slots of stator are 24T and the slots of rotor are 22T. We make a different design of the rotor to make the slots less but longer. This enables the rotor to run long time, a sort of fan rotor design. By using this stator rotor, you can reach low noise, long lifespan and low maintenance. Approved by IE2, IE3, and IE4 authentication.
140x70 mm Stator Rotor Lamination for Two Poles and Six Poles Motor
TG14070C
TG14070V have unique square design of stator outline goes with 34T rotor. This stator rotor is mostly applied for water pump motors, blower motors, and freezer compressor motors.The outer diameter of stator is 140 mm and the inner stator diameter is 70 mm. Most customers use it in two poles design with single phase or three phases induction motors, ranging from 1HP ~ 2HP. It's suit for the standard IEC frame no. 80The slots of stator are 24T and the slots of rotor are 34T. This is a standard 2 poles design motor, with big RPM and torque. This stator rotor lamination is great for pumps, blowers and angle grinders. By using this stator rotor, you can reach low noise, long lifespan and low maintenance. Approved by IE2, IE3, and IE4 authentication.
114X55 mm Stator Rotor Lamination for AC Motor
CD11455
The biggest different between CD11455 & TG11456 is the rotor. The rotor of TG11456 is “No Gap” and the rotor of CD11455 is not. The good benefit of CD11455 is that customers can lathe the rotor according to their desire outer diameter to meet with different demand on torque.This stator rotor / motor core is round shape and mostly applied for pump motors. The outer diameter is 114 mm and the inner diameter is 55 mm. Most customers use it in two poles design with single phase or three phases induction motors, ranging from 0.5HP ~ 1.5HP.The slots of stator are 24T and the slots of rotor are 29T. By using this stator rotor, you can reach low noise, long lifespan and low maintenance. Approved by IE2, IE3, and IE4 authentication.
Result 1 - 12 of 12
Hot Products
Motor Cores for Industrial Motor
TayGuei motor cores conform to high efficiency motor products of IE3 even IE4. Could increase...
Read More
Rotors & Stators for Pump Motor
Our tolerance value is 3µm. We are strict on our quality assurance to reduce the energy...
Read More